Not every truck lives on a motorway. Tipper trucks, distribution vehicles, logging trucks, refuse trucks and regional haulers all spend part of their lives on gravel, building sites, farm tracks or broken urban roads. A tire bought for the motorway will lose casings in those conditions, and a tire bought for quarries will cost fuel on the motorway. Bridgestone’s data book handles this with a service-category chart that rates each pattern from long haul to severe on/off-highway. This guide shows how to use that chart, compares the main on/off-highway and mixed-service models in it, and explains how to decide where your own operation sits.
The service categories in the data book
Bridgestone’s selection chart sorts tires into groups by service, and it shows which models suit each. The categories run from long-haul and regional-haul through local pickup and delivery, to on/off-highway, severe on/off-highway, off-highway and bus. The chart also indicates relative tire wear, from slower to faster, because tougher services wear tires faster whatever the pattern.
| Category | Typical vehicle | Main damage source |
|---|---|---|
| Long haul | Highway tractor-trailer | Normal wear, rolling resistance |
| Regional haul | Regional tractor, distribution | Wear, scrub, curb contact |
| Local, pickup and delivery | Urban distribution | Scrub, curbs, low speed turning |
| On/off-highway | Tipper, construction supply | Cuts, chips, gravel |
| Severe on/off-highway | Quarry, mining support | Heavy cuts, impact, stone drilling |
| Off-highway | Dedicated off-road | Severe cuts and abrasion |
Mixed service sits between regional haul and on/off-highway, which is the hardest zone to specify because both fuel and casing damage matter. A truck that does 70 percent motorway and 30 percent site work needs a different tire from one that does the reverse.
The on/off-highway models
The data book lists these on/off-highway and severe patterns:
| Model | Type | Notes from the data book |
|---|---|---|
| M863 | On/off-highway all-position | General on/off pattern |
| M840 | On/off-highway all-position | Rows such as 275/70R22.5 load range J |
| M857 | On/off-highway all-position | Rows such as 255/70R22.5 load range H |
| L320 | On/off-highway drive | Drive axle pattern for 11R22.5 |
| M775 | Severe on/off-highway drive | Heavy-duty drive pattern |
| M864, R244 | Wide-base all-position | Wide-base on/off options |
| L315 | Wide-base drive | Wide-base drive axle pattern |
| Greatec M853 | Wide-base all-position | Severe on/off-highway category |
There is also the R250 ED, an all-position radial with an extra-duty compound that resists cuts and chips. The data book recommends it for steering in high-scrub pickup and delivery and regional haul, and for mixed and moderate on/off-highway service. It is a good example of a tire built for the middle ground.
Load and pressure examples
Heavier-duty patterns often come with higher load ranges. A few rows illustrate this:
| Model and size | Load range | Single load at pressure | Dual load at pressure |
|---|---|---|---|
| L320 11R22.5 | G | 6,175 lb at 105 psi | 5,840 lb at 105 psi |
| M775 11R22.5 | H | 6,610 lb at 120 psi | 6,005 lb at 120 psi |
| M840 275/70R22.5 | J | 6,940 lb at 120 psi | 6,395 lb at 120 psi |
Two points matter. First, a higher load range gives more capacity and more cut resistance through a stronger casing, but the pressure needed to realize the capacity is higher. Second, high pressure is not a safe default. On rough surfaces a stiffer tire transmits more shock and may suffer more impact damage, while a very soft tire suffers sidewall flex damage. Set pressure by axle load, not by assumption; see our pressure chart guide and the Bridgestone data book guide to inflation and dual spacing.
How to decide where you sit
Measure your own mix rather than guessing.
- Ask drivers or use telematics to estimate the share of kilometers on unpaved or damaged surfaces.
- Record the causes of every tire removal for three months.
- Note the proportion of casings rejected at retreading.
- Compare fuel use with the tire family currently fitted.
If most removals are for cuts, chips and impact, move toward the on/off patterns. If most are for wear and the casings retread well, a regional or long-haul family will save more fuel. If it is mixed, consider an extra-duty compound on steer and a moderately aggressive drive pattern. Our guide to selecting truck tires by application gives a general process.
Casing protection in rough service
In mixed service, the casing is the asset. Several habits protect it.
- Remove stones from the grooves at every service, because stones drilled into the base cut the casing.
- Keep pressure correct. Underinflation on rough surfaces causes sidewall damage and heat build-up, as described in underinflation damage in truck tires.
- Avoid curb strikes and train drivers to approach them at a slow speed.
- Repair damage quickly. A small cut left to take in water can corrode steel cords.
- Remove tires in time for retreading; see hot retreading for truck fleets.
The Bridgestone text on cap and base compounding explains the logic: a slow-wearing cap with a cool-running base shields the casing from heat to help retreadability. Treat this as a design feature that helps, not a guarantee.
Wide-base in mixed service
The data book includes wide-base on/off patterns such as the M864, R244 and Greatec M853. A single wide tire replaces a dual pair, saving weight and reducing the number of sidewalls. But in rough service a single tire has no partner to carry the load if it is damaged, and a flat is more likely to strand the vehicle. Many fleets keep dual fitment for rough operations and use wide-base only where surfaces are predictable. Before specifying, read our guide to super single tire pressure.
Matching and mixing
On a mixed-service truck, you will often run a different pattern on steer and drive. That is fine, but do not mix patterns within an axle or within a dual pair. Keep diameters matched as described in dual tire pressure matching and diameter differences. A mismatched pair on rough ground is more likely to suffer overload on the larger tire.
Cost thinking
The most expensive mistake is to evaluate mixed-service tires on fuel alone. Add the cost of premature removals, downtime, towing and rejected casings. A tire that costs more but eliminates two roadside failures a year can pay for itself quickly. Combine these numbers using the total cost of ownership framework.
A site-visit checklist for mixed-service fleets
The surface your trucks meet is rarely written down anywhere, so see it for yourself. Once a year, ride along on a typical loop and note the following: how long the unpaved section is, whether it is loose gravel, packed dirt or broken concrete, whether there are sharp edges such as rebar or steel offcuts, and where the trucks turn tightly on abrasive surfaces. Photograph the entrance to the site, because potholes and ramps there often cause the worst impact damage. Share the notes with whoever specifies tires. A procurement decision made with this knowledge is almost always better than one based on a catalogue.
Driver behavior in rough service
Tire life on mixed routes depends heavily on the driver. Slow, wide turns on abrasive surfaces cut scrub wear. Avoiding spinning wheels on loose ground cuts drive tire wear and chip damage. Reporting every impact, even if the tire looks fine, allows an early inspection for bulges. Parking away from sharp debris, and walking around the vehicle before leaving a site, catches foreign objects before they cut. Training takes an hour and pays back quickly; give drivers a simple card showing the three most common damage causes on your routes.
Inspection frequency
Mixed-service trucks need more frequent inspections than motorway trucks. A practical schedule is a visual check at every shift change, a pressure check weekly and a full inspection, including groove stones and tread depth, every two weeks. Record every finding against the tire serial number. When a tire shows a cut that reaches the cords, remove it. Continuing to run it may cost the casing and cause a roadside failure.
Frequently asked questions
What is mixed service in truck tire terms?
It is a duty cycle that combines paved highway with unpaved, damaged or construction surfaces. It is harder to specify than pure highway or pure off-road use.
Which Bridgestone patterns suit on/off-highway use?
The data book lists the M863, M840 and M857 as on/off-highway all-position patterns, the L320 as a drive pattern and the M775 for severe service.
Should I run higher pressure on rough roads?
No. Use the pressure for your axle load. Overinflation can increase impact damage and underinflation causes sidewall damage.
Are wide-base tires good for off-road trucks?
Usually only for predictable surfaces. In rough service, dual fitment gives redundancy.
How do I know if my casings are suitable for retreading?
Ask your retreader for rejection data and the reasons for rejection.
Conclusion
Mixed service is where tire selection pays or punishes the most. Use Bridgestone’s service categories as a map, measure your own surface mix, match the pattern to the damage you actually see and protect the casing with pressure discipline and groove inspection. Then the extra cost of a tougher tire becomes a saving.